HIGH FRICTION SURFACING- HFS IS A
HIGH PERFORMANCE, CHEMICALLY ENGINEERED,
MODIFIED EPOXY RESIN SYSTEM SURFACED WITH A
CHOICE OF COLORED STONE AGGREGATE. USING
MANUAL OR AUTOMATED INSTALLATION METHODS,
THE SYSTEM PROVIDES A UNIQUE COATING ON
SUBSTRATE MATERIAL, RESISTING SEVERE
BRAKING, HEAVY WHEEL LOADING AND ALL TYPES
OF TURNING MOVEMENT. HFS ALSO IS RESISTANT
TO OIL, FUEL PRODUCTS AND DE-ICING PRODUCTS.
POLY FLEX TYPE 2
POLY
FLEX TYPE 2- 34518-32-GA1 Is a hot
applied, asphalt based product used to fill
cracks and joints in asphalt. Is supplied in
solid form. used in highway, street,
airfield, and parking lot pavements and is
applied to pavement cracks using pressure
feed melter application. Polyflex type 2
offers lower viscosity for easier
applications. Polyflex 2 is sold by the
pound
MARKER ADHESIVE
The
BAX 250 will heat 250 pounds of adhesive
per hour and applies 20 “shots” per minute
for a high application rate. The BAX comes
skid mounted. Comes equipped with a 10 foot
heated hose and a 24" wand providing
maneuverability and efficient production.
Optional hose and wands are available as
well a 60 Gallon unit.
CRAFCO Hot-Applied Flexible Pavement Marker
Adhesive is a hot-applied thermoplastic
bituminous material which, when properly
used and applied, bonds markers and
reflectors to both asphalt and concrete
pavement surfaces. Hot-Applied Flexible
Pavement Marker Adhesive is supplied as an
easy to use single component material which
is easily melted and poured or pumped onto
pavement surfaces. Since it is a hot melt
composition, Hot-Applied Flexible Marker
Adhesive sets up on cooling and is ready for
traffic in less than five minutes.
Hot-Applied Flexible Marker Adhesive is
formulated with premium asphalt, polymers
and additives to produce a unique material
which hold markers in place and remain
flexible at temperatures down to 20°F
(-7°C).
CRAFCO Hot-Applied Bituminous Marker
Adhesive is a hot-applied bituminous
material which, when properly used and
applied, bonds markers and reflectors to
both asphalt and concrete pavement surfaces.
The adhesive is supplied as an easy to use
single component material which is easily
melted and poured or pumped onto pavement
surfaces. Since it is a hot melt
composition, the adhesive sets up on cooling
and is ready for traffic in less than 5
minutes. Heating can be performed in either
directly or indirectly heated melting units.
The adhesive contains no rubber polymers
which can degrade at application
temperature.
PATCHING PRODUCTS
TechCrete
Crafco TechCrete is a proven hot pour
superior repair solution different from
conventional rigid repair methods. Due to
its flexibility, high tensile strength,
ability to bridge joints and high
compressive resistance, TechCrete creates a
long lasting concrete repair. PolyPatch Crafco PolyPatch has been specifically
designed for cracks too large for crack
sealing and distressed surfaces that are too
small for re-paving. It is a versatile
hot-applied, pourable, self-adhesive polymer
modified asphalt binder containing selected
aggregate to ensure good load bearing and
skid resistant characteristics. Compounded
with lightweight aggregate. Mastic One
Crafco Mastic One is designed for large
cracks and distressed surface areas too
small for re-paving. It is a versatile
hot-applied, pourable, self-adhesive polymer
modified asphalt binder containing selected
aggregate to ensure good load bearing and
skid resistant characteristics. Compounded
with standard weight aggregate. QPR
Whether it is repairing utility cuts or
patching that reoccurring pothole, QPR high
performance cold patch is ideal for all
weather conditions. QPR is specifically
formulated for the wide-ranging temperature
and climate of all areas. QPR is permanent,
fully guaranteed against any failure, and
most important, does the job right the first
time.
GeoTac is a peel-and stick waterproofing
membrane designed specifically as a moisture
barrier. It prevents water permeation or
penetration through pavement surfaces and
subsequent damage that moisture causes.
GeoTac is high caliber with a full modified
SBS asphalt mastic applied to a non woven
polyester geotextile.
PavePrep is a high density mastic
laminated with a tough woven polyester
designed to withstand the loads encountered
by highway traffic and stress concentrations
at pavement joints and cracks. PavePrep’s
dense and flexible mastic reduces crack
reflection through the overlay.
• Biodegradable
• Non-Toxic
• Non-Hazardous
• Non-Corrosive
• Non-Ozone Depleting
• Free of Phenols, Phosphates, Heavy
Metals
• No VOC
• Low Odor
CRAFCO ROAD SAVER ASPHALT REMOVER-Low
odor, non-hazardous and environmentally
friendly, everything you ever wanted in a
cleaner. This new cleaner from Crafco
dissolves grease, oil, asphalt and sealant
while it protects the paint finish on the
equipment surface being cleaned. Crafco
RoadSaver Sealant & Asphalt Remover removes
sealant, tar and oil from paving tools,
truck beds, spreaders, equipment and any
surface that needs cleaning. It’s
biodegradable, effectively dissolving
sealant and asphalt build up on all painted
or unpainted surface leaving an invisible
protective coating to help reduce future
buildup.
DETACK
Open
freshly crack- sealed pavements to vehicle
and pedestrian traffic immediately and
eliminate sealant pick-up and tracking with
DETACK. DETACK is an economical,
biodegradable liquid from Crafco that
eliminates sealant tack when sprayed onto
freshly applied hot pour sealant. Now you
don’t have to wait until the sealant has
cooled before opening the pavement to
traffic. DETACK application is a one-man
operation that saves money, time, and
increases efficiency. DETACK is the smart
choice over messy sand, aggregate, or toilet
paper applications and reduces set up and
tear down time for lane closures. If you’re
stuck for an economical, time saving,
detackifying solution for hot pour sealant
then DETACK from Crafco is your answer.
EMULSION TANK
Keeping
emulsions from extreme temperatures is one
of the most important storage and handling
practices. Asphalt emulsions should not be
frozen or boiled because it will not
reconstitute. Excessive heating will cause
the emulsions to fall apart and break. It is
also important to circulate stored
emulsions. Failing to properly store
emulsions will provide inferior application
performance, often times poorly contained
emulsions can and will cause a project to
fail.
Crafco Emulsion tanks store emulsions at
manufactures recommended temperatures and
keep the emulsion circulated while in
storage, all done easily digitally
controlled.
Crafco Emulsion Storage Tanks conveniently
store emulsions on site for immediate use at
truck load prices. They are available in
2,3,4,5,6,8, and 10 thousand gallon sizes.
The Emulsion tank has 3” insulation with a
10-gauge steel secondary containment shell
featuring an electric top-mount mixer.
Options include an electric timer,
mechanical float gauge, and an access ladder
with cage.
